Ark How To Set Up Irrigation

Download Article

Download Article

Irrigation systems are a simple, safe, and efficient way to water your yard or garden. As long as you lot have the right materials, your irrigation system can water individual plants or cover large areas of your one thousand. Lay out your piping and adhere the watering devices to create the safest and most efficient system possible. After a few hours of hard piece of work, you'll accept a prophylactic and efficient yard irrigation system.

1. one

   Install a dripper system to water private plants. Dripper irrigation systems provide a steady flow of water to individual plants. If you want to h2o each plant on its own, cull a dripper system to give your plants a direct water source.^[1]

   • A dripper system consists of many foursquare, flat waterspout-similar "drippers" hooked to your irrigation pipage that emit a minor, steady water flow.
   • Dripper systems also work well for potted outdoor plants.
   • If yous have a big thou or desire to cover more area, you may want to choose another system.

2. ii

   Choose a sprinkler irrigation organisation to comprehend more than distance. Sprinkler heads can h2o a radius between iii feet (0.91 1000) to 30 feet (9.1 thou), depending on the period rate and water pressure. Pick a sprinkler system if you have a large k that needs even watering.^[2]

   • Sprinkler irrigation systems consist of many sprinkler bulbs hooked to the irrigation piping that spray water out of their nozzles.

   Advertizement

3. 3

   Buy a sprayer or bubbler organisation as a hybrid between drippers and sprinklers. Sprayers and bubblers have adjustable radiuses and tin provide either direct or general attention to plants in your yard. Choose a bubbler or sprayer system if y'all want to control the amount of directly water flow your plants get at a given fourth dimension.^[iii]

   • Sprayer and bubbler systems look like a cross between sprinklers and bubblers. They are generally flat and square, with a nozzle on top that sprays a steady water flow.
   • Bubbler and sprayer systems tend to have a smaller radius than sprinkler systems.

Advert

1. 1

   Measure your yard's perimeter and area. Take measurements of the perimeter and area of your yard. Take measurements of the length and width, then multiply these numbers to find the land's full surface area.

   • Work slowly to keep the state'southward measurements equally accurate as possible.

2. ii

   Purchase grid paper to map out your irrigation system. Grid newspaper can keep your drawing precise. Assign each grid a certain altitude to help you visualize your backyard and plan an accurate layout.

   • Yous might assign each grid, for example, a distance of 1 square human foot (0.093 square meters).

3. iii

   Draw an approximate layout of the irrigation organisation. Using your grand measurements, map out an guess layout of your yard. Marker your 1000's h2o source, power source, main plants or garden areas, and areas where you will install the irrigation tubing.^[4]

   • The water source is more often than not the outdoor faucet, and the power source is the way yous'll turn the organization on and off.
   • Utilize a pencil while designing the layout in example y'all need to make changes or correct mistakes.

Advertisement

1. ane

   Attach a vacuum breaker to the outdoor faucet and irrigation tubing. Vacuum breakers prevent contaminated water in your irrigation system from washing back up into your home's water supply. Screw the vacuum breaker onto your outdoor faucet, and attach your irrigation tubing to the contrary side of the vacuum billow.^[5]

   • Vacuum billow are cylindrical metallic tubes that screw into your home'south outdoor faucet at the elevation.
   • You can buy vacuum breakers from nigh garden centers or home improvement stores.

2. 2

   Spread the irrigation tubing effectually your yard based on your layout plans. Position ⁱ⁄_ii  in (1.3 cm) poly tubing forth the areas that you plan to water with the irrigation system. Cut the tubing with pruning shears when yous have reached the end length of your organization or areas where y'all will demand to make angles.

   • Let your tubing sit in the sun for several hours before using it to make it more than flexible and easier to piece of work with.
   • You tin can buy poly tubing from well-nigh hardware or dwelling improvement stores.

3. 3

   Use 90-degree fittings to make bends in the layout, if needed. If you want your system to turn at an angle, cut the tubing with pruning shears and printing its end into a 90-degree fitting, twisting it in place. Attach the other end of the xc-degree plumbing equipment to the reverse half of the tubing to continue laying out your system.^[6]

   • Buy 90-degree fittings online or from about domicile improvement stores.
   • You lot can as well use T-fittings as an alternative using the same method. A T-plumbing equipment is a tube that bends at a slight angle to conform turns in your irrigation layout.

4. 4

   Install a ground stake every i–2 feet (0.30–0.61 thousand) to pin the tubing in place. Hook the top of the basis stake over the tubing and pivot it to the ground. This will prevent the tubing from moving around when you plough on the water.^[vii]

   • Look for basis stakes at a home improvement store or garden center.

5. 5

   Close the tubing close with a tubing clamp. When yous've laid out all of the tubing, turn on the water for a few minutes to affluent out the dirt from the system. Slide a tubing clamp the approximate size of the tubing around the end of the arrangement to crimp it shut and avoid waterlogging an surface area of your yard.^[eight]

   • Plough off the water before clamping your tubing close.
   • Tubing clamps are small-scale, oval-shaped metal clips that secure open up tubing ends. You tin buy these clamps from about hardware or habitation comeback stores.

Advertisement

1. 1

   Punch ¹⁄₄  in (0.64 cm) wide holes into the tubing. Use a pigsty punch tool to marker wherever you lot want to install a sprinkler, bubbler, dripper, or sprayer. Button the hole dial firmly into the tubing and twist information technology until it makes a complete, clean hole through the other side.^[9]

2. 2

   Attach ¹⁄₄  in (0.64 cm) poly tubing to the holes with a barbed connector. Push button the barbed connector through the hole in the irrigation tubing. Attach a length of ¹⁄₄  in (0.64 cm) tubing to the reverse side of the barbed connector, cutting it with pruning shears when it reaches the area that y'all want to water.^[10]

   • You can find barbed connectors, which are cylindrical metal tubing connectors, and ⁱ⁄_iv  in (0.64 cm) tubing from most home improvement stores.

3. iii

   Install the watering device at the end of the ^one⁄₄  in (0.64 cm) tubing. Attach the dripper, sprayer, bubbler, or sprinkler by connecting information technology through the terminate of the ^ane⁄₄  in (0.64 cm). To hold it in place, attach a small gardening stake to the stop and printing it into the ground virtually the area it needs to comprehend.^[xi]

4. 4

   Flush and examination the irrigation system via the outdoor faucet. Turn on your outdoor faucet to affluent out whatever remaining dirt and test your irrigation system. Arrange the positioning of the watering devices or add more as needed.

   • If you lot observe any issues with a watering device, check the ⁱ⁄₄  in (0.64 cm) tubing to make certain it is fastened securely.

Advertisement

Add together New Question

• Question

  How practice yous set a leaking irrigation system?

  

  Mike Garcia is a Licensed Landscape Contractor and the Founder of Enviroscape LA, a full-service landscape pattern and structure firm in Los Angeles, California. With over 30 years of experience, Mike specializes in sustainable landscape practices. Mike holds an Ornamental Horticulture degree, C-27 Landscape Contractor and D-49 Tree Service Contractor licenses, and Permaculture Blueprint, California Naturalist, International Certified Professional Swimming Contractor, and Pond Building certifications. He is one of eight Internationally Certified Pond Builders in the globe. Enviroscape LA has won landscape and h2o feature awards from the International Professional Pond Contractors Association (IPPCA), National Association of Pond Professionals (NAPP), and the California Landscape Contractors Association (CLCA). Mike is a by president of the CLCA and currently serves on their local Board of Directors. Enviroscape LA has been featured in PONDS USA Magazine, Pond and Garden Lifestyles Magazine, and the Los Angeles Times. Mike has appeared on Extreme Home Makeover, HGTV'southward Landscapers Claiming, and A & E'south series Fix That One thousand.

  

  Licensed Landscape Contractor

  Proficient Reply

  

  Support wikiHow by unlocking this expert answer.

  With an overhead irrigation system, if you've adamant that at that place's a leak, then you need to determine where the leak is coming from. If it'south coming from the top part called the nozzle, that but unscrews. Unscrew the broken nozzle so spiral a new ane on. In the case of baste irrigation, a lot of times some of the drip irrigation will go punctured on blow. In that instance, once yous open up the line and determine where the leak is, cut the cleaved drip and put pressure level on both ends. Push on information technology, and it'll be practiced every bit new.

Ask a Question

200 characters left

Include your electronic mail accost to get a message when this question is answered.

Submit

Advertisement

• If you have problem installing your irrigation organisation, hire a landscaper for professional guidance.

• To give your irrigation organisation a manicured advent and help it blend in with your garden, cover the tubing with a thin layer of mulch.^[12]

Advertisement

• Installing a vacuum breaker is essential to avoid water contamination. Attaching a vacuum breaker to your outdoor faucet first before setting upwardly your arrangement.

Advertisement

Things You'll Need

• Grid paper
• Vacuum breaker
• ¹⁄_two  in (1.3 cm) poly tubing
• ¹⁄_iv  in (0.64 cm) poly tubing
• 90-caste fittings
• Ground stakes
• Tubing clench
• Hole punch
• Barbed connectors
• Garden stakes
• Watering device (dripper, sprinkler, sprayer, or bubbler)

Most This Article

Thanks to all authors for creating a page that has been read 42,756 times.

Did this article help you?

Source: https://www.wikihow.com/Install-an-Irrigation-System

Share this post